Total Solution for Construction & Waterproofing.
- (+91) 9137627832
- nilesh.riddhienterprise@gmail.com
- 218,Sagar Prabhat,Co-Op Industrial Estate, Dahisar Check Naka, Dahisar(East), Mumbai, Maharashtra, India. 400068
© 2020 Riddhi Enterprise. All Rights Reserved
TAMPUR 130
GCP HA CUT AF
TAMPUR 125
TAMPUR 136
GCP ROCKSTAB 1:2
GCP ROCKSTAB WXSG
GCP HA FLEX LV AF
GCP HA SAFEFOAM
X INJECT WS 100
TAMPUR 116T
ACY-808
CRM-120
CRR-100
CY-505
CYH-202
CYH-303
GCP GELACRYL
HEL-080
RPU 500
CRP-105
CY-101
TAMPUR 130
TamPur 130 / TamKat 130 is a single-shot hydrophobic polyurethane based on MDI in combination with polyether polyols and an amine based catalyst. The system only reacts when it comes into contact with water, producing a semi-flexible polyurethane foam.
GCP HA CUT AF
Next generation, phthalate free, closed cell, 1-component, high performance, low viscosity, hydrophobic, HydroActive, rigid polyurethane injection grout for cutting off gushing water leaks with a high flow rate and/or high hydrostatic pressure.
TAMPUR 125
Tampur 125 is based on a polyol component (part A) and a polymeric MDI (part B). When mixed, a hydrophobic polyurethane foam is formed which is tough, rigid and resistant to a wide range of chemicals. TamPur 125 reacts rapidly enabling the product to cut off large water leaks.
TAMPUR 136
Tampur 136 is a single component hydrophobic polyurethane based on MDI in combination with polyether polyols. The system incorporates an active accelerator and only reacts when it comes into contact with water, producing a non-toxic, semi-flexible polyurethane foam.
GCP ROCKSTAB 1:2
Phthalate-free, fast-acting, 2-part, pre-catalyzed, rigid foam polyurethane injection system for structural injections requiring high compressive strength
RockStab resins are phthalate-free, 2-component injection resins consisting of a resin and a hardener that are pumped in a 1/1 mix ratio. After mixing the two components in a 1/1 ratio through a special mixing head with static mixer, the resin hardens into a hard foam, a very hard foam, or a hard plastic, depending on the type of Rockstab used.
Faster response times can be obtained by using an optional accelerator.
GCP ROCKSTAB WXSG
Phthalate-free, highly reactive 2-component polyurethane system for waterproofing injections where high compressive strengths are required
Product Description:
Rockstab WX SG is a 2-component, phthalate-free, fast-reacting resin with high compressive strength upon curing. When injected in dry conditions through the specially designed 2-component injection head with static mixer, Rockstab WX SG quickly cures to a very hard material with high compressive strength. If Rockstab WX SG comes into contact with water during the reaction, the resin will foam and cure rapidly to a tough, rigid, closed cell polyurethane foam that is generally unaffected by aggressive environments.
GCP HA FLEX LV AF
1-component, phthalate-free, closed-cell, hydrophobic, water-reactive, flexible, high performance polyurethane injection resin for waterproofing construction joints and cracks in concrete structures
Product Description
Unreacted, HA Flex LV AF is a yellow, non-flammable liquid without phthalate plasticizers. HA Flex LV AF are next generation 1-component injection resins with improved waterproofing properties. In contact with water, the resin will expand and quickly (depending on the temperature and amount of HA Flex Cat AF used) cure to a tough, flexible, closed-cell polyurethane foam that is generally inert to corrosive environments.
GCP HA SAFEFOAM
Phthalate-free, flexible, hydrophilic, low-viscous polyurethane resin for sealing moving, non-structural cracks
X INJECT WS 100
X-Inject WS100 is a two part Base (Part A) and Catalyst
(Part B) solvent-free, low viscosity, foaming
polyurethane resin system. When in contact with water
it reacts to form a rapidly expanding stable foam that
stops water leaks.
X-Inject WS100 is formulated to temporarily seal water
leaks in concrete structures to allow injection of a
secondary permanent seal using X-Inject PU211 or
PU221.
TAMPUR 116T
TAMPUR 116T is a two-component, silicate modified, solventfree, semi-flexible polyurethane injection resin. It is
specifically designed for rapid stabilisation of coal,
concrete and soft ground geologies, providing structural
integrity, strength and flexibility. Its superior performance
allows TamPur 116T to be used as a Chemical “Rock Bolt
Resin” and on-site tests have demonstrated pull-out
strengths in excess of 31 tonnes.
ACY-808
Acrylic Water Base
Feature
- Double component type grouting pump with high performance(Running by electric motor).
- Pump discharges with accurate 1:1 mixing ratio.
- It is developed for using rapidly-hardening type product.
- It is possible to adjust hardening time by controlling the catalyst amount.
- It is easy to use and move(Portable, 29kg) at job site, and wheel-stopper makes no-move at slope.
- After using, it is easy cleaning up, just by using water.
- It is easy to change spare parts.
- All parts contacting with acryl is made stainless steel.
CRM-120
Injection Grouting Chemical
EXTRA-RAPID SETTING MORTAR for Repair
Feature
- Waterstop
- Quick setting
- Sealing water leaks in 2~3 minutes
- Suitable for vertical and horizontal concrete surfaces
- Non toxic
- CRM-120’s applicable temperature is +5℃~+30℃.
- May be differ the curing time according to temperature and
humidity at the construction site.
- It is recommended to store the materials in a cool place.
During the summer season and maintain water temperature
lower prior to using.
- If necessary, take appropriate measures, e.g. Use warm water
if ambient temperature is low.
- Do not add additives or any other dusts with CRM-120.
- CRM-120 contains cement and produces an alkaline reaction
with water. So protect skin and eye's during application.
If contact occurs, wash thoroughly with water.
CRR-100
Carbon Fiber Resin
Injection Grouting Chemical
Carbon Fiber Epoxy Resin CRR-100 is a
reinforcing epoxy resin which can increase
the performance of carbon fiber with the
outstanding resistance to chemical and water.
It is suitable for structural reinforcement as it
offers a compelling adhesion performance on
concrete and carbon fiber sheet.
CY-505
Double Component Type High Strength Polyurethane Water Stop Material
CY-505 is Double component type hydrophobic polyurethane resin that
cuts off water from cracks and reinforces the maintenance
works on concrete structures, subways and tunnels.
It is a low expansion water stop reinforcing agent of which
the water reaction expansion ratio is minimized.
Compared to conventional polyurethane water stop
materials, it is stronger and its hardened foam is
more rigid. It does not generates defects
by foam deformation and
it provides virtually permanent
water stop effect.
CYH-202
CYH-202
Single Component Semi-rigid Polyurethane
Injection Grouting Chemical
CYH-202 Semi-hydrophobic Polyurethane Grouting is
used to stop leaks and fill underground voids.
CYH-202 is a polymer solution which cures
when reacted with water,
CYH-202 can not only stop the water,
but also it can stop or slow
the deterioration of steel bar or
other internal features of the concrete.
This success is due to
the placement of CYH-202
throughout the depth of the crack.
CYH-303
CYH-303
High Flexible PU Foam (Double Components Type)
Injection Grouting Chemical
CYH-303 is self-reacting of double components(Resin & Hardener) type
hydrophilic polyurethane which has polyether polyol properties.
CYH-303 applies to the leakage area for the waterstops where has vibration also
because it has elastic property foaming ratio with water is very lower than normal PU foam (Hydrophobic type).
CYH-303 density is high and hardened foam is same like a rubber. Therefore, it is useful for the expansion joints and water
leakage caused by deformation. Waterproof effects last semi-permanently.
It provides strong physical strength after contact with water.
So these properties brings excellent bonding strength to give
the waterproof ability and reinforcement. It is high elastic PU material.
GCP GELACRYL
GELACRYL Superflex 2-component acrylic built resin
GELACRYL™ SuperflexGelacryl Superflex is a 2-component acrylic based resin developed for injection into pores, cracks, capillaries, voids and honeycombed concrete.
HEL-080
Double Component Low Viscosity Wet Epoxy Injection Agent
It is a specialized repair and reinforcement material that
is injected to cracks with wet to keep the initial concrete state
by maintaining the best adhesiveness.
The humidity, moisture, and oil at construction structure
cause a damage to the chemical reaction of between
epoxy resin and hardener, and cause the decrease of
strength, adhesion.
HEL-080 is epoxy for wet by increasing hydrophile,
as the solution of the problem.
HEL-080 is a specialized in the cracks with wet, moisture,
humidity. HEL-080 is low viscosity, which is capable of
injecting into fine cracks.
RPU 500
Low viscous, Single Component, hydrophobic, MDI-based, polyurethane injection resin without catalyst. It only reacts with water and forms a Flexible Polyurethane Foam. This product can be injected pure directly into a leaking crack, fracture or joint. After injection has taken place, the will foam to expand and fill the void, forming a tight, impermeable elastomeric seal, stopping the water flow.
CRP-105
CRP-105
Carbon Fiber Primer
Carbon Fiber Epoxy Primer CRP-105
contains epoxy resin and Polyamide as
primary substances. It has a short pot life
and has excellent chemical and water
resistance. It penetrates to concrete
surface to strengthen adhesion
performance.
CY-101
CY-101
Single Component Hydrophilic Polyurethane
Injection Grouting Chemical
CY-101 Hydrophilic Polyurethane Grouting is
used to stop leaks and fill underground voids.
CY-101 is a polymer solution which cures
when reacted with water,
CY-101 can stop the water,
it can stop or slow the deterioration of
steel bar or other internal features of
the concrete. This success is due to
the placement of CY-101
throughout the depth of the crack.